Oscilloscope 7603

Tektronix; Portland, OR

Daten
Forum
Bilder
Sammlungen

  • Jahr
  • 1973
  • Kategorie
  • Service- oder Labor-Ausrüstung
  • Radiomuseum.org ID
  • 225490

 Technische Daten

  • Anzahl Röhren
  • 1
  • Röhren
  • Anzahl Transistoren
  • Halbleiter vorhanden.
  • Halbleiter
  • Hauptprinzip
  • kein Zusatz
  • Wellenbereiche
  • - ohne
  • Betriebsart / Volt
  • Wechselstromspeisung / 100; 110; 120; 200; 220; 240 Volt
  • Lautsprecher
  • - - Kein Ausgang für Schallwiedergabe.
  • Material
  • Metallausführung
  • von Radiomuseum.org
  • Modell: Oscilloscope 7603 - Tektronix; Portland, OR
  • Form
  • Tischmodell, Zusatz nicht bekannt - allgemein.
  • Abmessungen (BHT)
  • 8.7 x 11.4 x 24 inch / 221 x 290 x 610 mm
  • Bemerkung

  • VERTICAL SYSTEM

    Channels: Two left-hand plug-in compartments; compatible with all 7000-Series plug-ins. Bandwidth determined by mainframe and plug-in unit

    Modes of Operation: LEFT, ALT, ADD, CHOP, RIGHT.

    Chopped Mode: Repetition rate is approximately 1 MHz.

    Delay Line: Permits viewing leading edge of displayed waveform.


    HORIZONTAL SYSTEM

    Channels: One right-hand plug-in compartment; compatible with all 7000-Series plug-ins.

    Fastest Calibrated Sweep Rate:  5 ns/div with the 7B53A or 71353AN.
    X-Y Mode: The phase shift between vertical and horizontal channels is 2° from DC to 35 kHz. Bandwidth is DC to at least 2 MHz.


    CRT AND DISPLAY FEATURES

    Standard: Internal 8 x 10 div (1.22 cm/div) graticule with variable Illumination. Accelerating potential is 15 kV with P31 phosphor standard.

    Option 4, Maximum Brightness CRT: Internal 8 x 10-cm graticule with variable illumination. Accelerating potential is 18 kV with P31 phosphor standard, P11 optional.

    Option 8, Phosphor Change (Specify): Standard CRT: P1, P2, P7, P11, P7SA (Phosphor/Spectrum Analyzer graticule combination); Maximum Brightness CRT: P11.

    Auto-Focus: Reduces the need for additional manual focusing with changes in intensity after focus control has been initially set.

    Beam Finder: limits display within graticule area.
     

    used CRT's (V1099)

                       from SN       to   SN      
    154-0640-00   B010100 - B019999
    154-0640-05   B020000 - B327256
    154-0640-10   B327257
    154-0672-002 XB030492
    154-0673-003

    2 Option 4 only
    3 Option 6 only
     

    see Forum

  • Nettogewicht
  • 30 lb 0 oz (30 lb) / 13.620 kg
  • Originalpreis
  • 1,600.00 USD
  • Datenherkunft
  • -- Original prospect or advert
  • Autor
  • Modellseite von Pius Steiner angelegt. Siehe bei "Änderungsvorschlag" für weitere Mitarbeit.

 Sammlungen | Museen | Literatur

Sammlungen

Das Modell Oscilloscope befindet sich in den Sammlungen folgender Mitglieder.

 Forum

Forumsbeiträge zum Modell: Tektronix; Portland,: Oscilloscope 7603

Threads: 1 | Posts: 2

Guest Leo Potjewijd of the Netherlands writes:

Although the 1973 TEK catalog does list option 8 as a phosphor change, numerous instances (like the attached, undated product sheet) list option 8 as a protective cover. In fact, I own a 7603 scope with option 8 (sticker inside) and that is indeed equipped with a protective cover.
The 1974 catalog does not list an option 8 for the 7603 anymore...
It appears to me that the phosphor change option as listed in the 1973 catalog was too unclear and therefore later replaced by the options 13, 71, 72, 76, 77 and 78.

 

Michael Watterson, 23.Jan.14

Weitere Posts (2) zu diesem Thema.