T3 190, 193 Series
Detrola; Detroit (MI)
- País
- Estados Unidos
- Fabricante / Marca
- Detrola; Detroit (MI)
- Año
- 1938
- Categoría
- Radio - o Sintonizador pasado WW2
- Radiomuseum.org ID
- 37406
Haga clic en la miniatura esquemática para solicitarlo como documento gratuito.
- Numero de valvulas
- 8
- Principio principal
- Superheterodino en general; ZF/IF 456 kHz; 2 Etapas de AF
- Número de circuitos sintonía
- 7 Circuíto(s) AM
- Gama de ondas
- OM, OC y banda Pesquera (policia USA)
- Tensión de funcionamiento
- Red: Corriente alterna (CA, Inglés = AC) / 115 Volt
- Altavoz
- Altavoz electrodinámico (bobina de campo)
- Material
- Madera
- de Radiomuseum.org
- Modelo: T3 190, 193 Series - Detrola; Detroit MI
- Forma
- Sobremesa de botonera.
- Anotaciones
-
BC 540-1600 kHz), TROP (1650-5400 kHz) and SW (5.4-16.0 MHz) bands.
John F. Rider schematic Detrola Page 9-1 shows Models 175 Series (T1, C1), 190, 193 Series (T2, T3), and 195 Series (C4). The alignment procedure is the same as the 185 Series.
- Ext. procedencia de los datos
- Ernst Erb
- Procedencia de los datos
- Machine Age to Jet Age III
- Referencia esquema
- Rider's Perpetual, Volume 9 = 1938 and before
- Otros modelos
-
Donde encontrará 334 modelos, 195 con imágenes y 291 con esquemas.
Ir al listado general de Detrola; Detroit (MI)
Contribuciones en el Foro acerca de este modelo: Detrola; Detroit MI: T3 190, 193 Series
Hilos: 1 | Mensajes: 13
Jeffrey D Angus wrote:
Some of the test equipment I'm using on this train wreck.
HP 3325A synthesized signal generator. (Makes a very nice sweeper.)
Tektronix 422 dual channel scope. (Run of the mill, but nice.)
Motorola R-2018 Service Monitor. (Using it as a spectrum analyzer.)
Using the sweeper at 436 KHz to 476 KHz I get about a 15 KHz wide
peak at 456KHz through the IF transformers. I have to scope connected
to the top of the volume control so I can set the sweep rate at
0.05 seconds per sweep.
Using the sweep generator set at both 1500 KHz and 600 KHz, all of
the trimmer capacitors (and main tuning caps) appear to be working
properly as far at physically and electrically.
But... The radio is deaf as a post. I can only hear a couple of the
local flame thrower stations and only just barely above the noise.
Using the spectrum analyzer with a short wire pickup probe inside
either of the IF transformer cans, I'm seeing a pass band of noise
that is 30 dB above the noise floor. This is apparently enough to
fully close the eye tube with the detected noise and subsequent
AVC voltage.
Now, I've pulled the grid cap of of the 6D6 IF amplifier and the
wide band high level noise is still there in the 1st IF can.
Grounding the 6A7 mixer input grid cap with a .01 uF capacitor
eliminates the noise. (along with everything else)
This radio is the one with the motorized tuning. The push buttons
go to settable commutator stops to position the main tuning cap.
They do not go to additional antenna and local oscillator coils.
As yet another attempt in solving this problem, I took a 7 pin tube
base and an octal socket and made a "6A8 for 6A7" tube adaptor. It
actually works, shifted the receive frequency down a little bit, but
is still deaf as a post.
The basic B+ as measured off of the rectifier (and supplying the
plates of various tubes is about 220 VDC.
At this stage, I'm about ready to gut the mixer and IF section and
install a 6BE6 and 6AU6 with a couple of K-tran IF transformers and
call it day.
(Yes, I've been fighting this one for 3 weeks now.)
Jeff
Electrically, it is identical to a Detrola 190.
6A7, 6D6, 75, 76, 42, 42, 6G5 and 80 rectifier.
http://www.nostalgiaair.org/PagesByModel/919/M0003919.pdf
The problem:
Lots of inter station white noise. Like what you'd expect from
a "hot" receiver, except... it's deaf as a post only able to
hear the local flamethrower stations.
I've checked the B+, and the AVC voltages. They are as one would
expect. But occasionally, the radio will go up and back down in
volume. Very annoying.
Some of the test equipment I'm using on this train wreck.
HP 3325A synthesized signal generator. (Makes a very nice sweeper.)
Tektronix 422 dual channel scope. (Run of the mill, but nice.)
Motorola R-2018 Service Monitor. (Using it as a spectrum analyzer.)
Using the sweeper at 436 KHz to 476 KHz I get about a 15 KHz wide
peak at 456KHz through the IF transformers. I have to scope connected
to the top of the volume control so I can set the sweep rate at
0.05 seconds per sweep.
Using the sweep generator set at both 1500 KHz and 600 KHz, all of
the trimmer capacitors (and main tuning caps) appear to be working
properly as far at physically and electrically.
But... The radio is deaf as a post. I can only hear a couple of the
local flame thrower stations and only just barely above the noise.
Using the spectrum analyzer with a short wire pickup probe inside
either of the IF transformer cans, I'm seeing a pass band of noise
that is 30 dB above the noise floor. This is apparently enough to
fully close the eye tube with the detected noise and subsequent
AVC voltage.
Now, I've pulled the grid cap of of the 6D6 IF amplifier and the
wide band high level noise is still there in the 1st IF can.
Grounding the 6A7 mixer input grid cap with a .01 uF capacitor
eliminates the noise. (along with everything else)
This radio is the one with the motorized tuning. The push buttons
go to settable commutator stops to position the main tuning cap.
They do not go to additional antenna and local oscillator coils.
As yet another attempt in solving this problem, I took a 7 pin tube
base and an octal socket and made a "6A8 for 6A7" tube adaptor. It
actually works, shifted the receive frequency down a little bit, but
is still deaf as a post.
The basic B+ as measured off of the rectifier (and supplying the
plates of various tubes is about 220 VDC.
At this stage, I'm about ready to gut the mixer and IF section and
install a 6BE6 and 6AU6 with a couple of K-tran IF transformers and
call it day.
(Yes, I've been fighting this one for 3 weeks now.)
Jeff
Jeffrey Angus, 29.Sep.08