5P32E Ch= HS-559

5P32E Ch= HS-559; Motorola Inc. ex (ID = 2406096) Radio
5P32E Ch= HS-559; Motorola Inc. ex (ID = 2406097) Radio
5P32E Ch= HS-559; Motorola Inc. ex (ID = 2406098) Radio
5P32E Ch= HS-559; Motorola Inc. ex (ID = 2406099) Radio
5P32E Ch= HS-559; Motorola Inc. ex (ID = 138723) Radio
5P32E Ch= HS-559; Motorola Inc. ex (ID = 289139) Radio 5P32E Ch= HS-559; Motorola Inc. ex (ID = 289140) Radio
Utilice la barra deslizante rojo por más.
5P32E Ch= HS-559; Motorola Inc. ex (ID = 289139) Radio
Motorola Inc. ex: 5P32E Ch= HS-559 [Radio] ID = 289139 683x532
Seleccione una imagen o esquema para mostrar las miniaturas de la derecha y haga clic para descargar.
For model 5P32E Ch= HS-559, Motorola Inc. (ex Galvin Mfg.Co. Chicago); Schaumburg (IL):
Ebay Nr. 220070309226 Bild bearbeitet.
País:  Estados Unidos
Fabricante / Marca:  Motorola Inc. (ex Galvin Mfg.Co. Chicago); Schaumburg (IL)
Año: 1957 ? Categoría: Radio - o Sintonizador pasado WW2
Válvulas 4: 1R5 1U4 1DN5 3V4
Principio principal Superheterodino en general; ZF/IF 455 kHz; 2 Etapas de AF
Número de circuitos sintonía 6 Circuíto(s) AM
Gama de ondas OM (onda media) solamente
Tensión de funcionamiento Red / Baterías o pilas / (7.5; 90); AC/DC 117 Volt
Altavoz Altavoz dinámico (de imán permanente) / Ø 4 inch = 10.2 cm
Potencia de salida
de Modelo: 5P32E Ch= HS-559 - Motorola Inc. ex Galvin Mfg.Co
Material Plástico moderno (Nunca bakelita o catalina)
Forma Portátil > 20 cm (sin la necesidad de una red)

Color= Navy leatherette. See here about Tinkertoy technique. The Beitman R-18 shows the following models with this chassis HS-559: 5P31A, 5P32C, 5P32E, 5P32R and 5P32Y but also 5P33EW, 5P33VW and 5P33W for chassis HS-561. See also 66L1 and 66L2 with Tinkertoy technique.

Referencia esquema Beitman Radio Diagrams Vol. 18, 1958
Mencionado en Collector's Guide to Antique Radios (6th edition)
Documentación / Esquemas (1) Photofact Folder, Howard W. SAMS (Set 363 Folder 14 Dated 7-57)

Modelo creado por Egon Penker. Ver en "Modificar Ficha" los participantes posteriores.

Ir al listado general de Motorola Inc. (ex Galvin Mfg.Co. Chicago); Schaumburg (IL)
Donde encontrará 4105 modelos, 2817 con imágenes y 3743 con esquemas.


Contribuciones en el Foro acerca de este modelo
Motorola Inc. ex: 5P32E Ch= HS-559
Hilos: 1 | Mensajes: 1
Entradas: 1240     Réplicas: 0
motorola: HS-559 Feedforward AVC
Joe Sousa

Fellow Radiophiles,

As I was organizing some battery tubes in my replacement stock, I came across the 1DN5.

This is a very unusual remote cut-off Audio pentode for use in AC/DC portable radios that use a 50mA filament series string. There is also an additional anode near the negative end of the filament to serve as the diode detector.

Our database shows two Motorola AC/DC portable chassis that use this tube for the same purpose: HS-559 and HS-647.

The filaments of the 4 tubes in the radio are wired in series starting from ground:

1R5 pentagrid converter

1DN5 Detector, AVC, Audio preamp

1U4 IF pentode

3V4 audio power

The voltage at the top of the 50mA filamentary string is 7.5VDC, which may come for the A battery, or from a high power 2K resistor tied the +95V, which dissipates about 5W when the radio is under AC power.

The 1DN5 is the audio preamp, but with the AVC voltage applied to the control grid as it's source of bias. The gain of the audio preamp depends on the strength of the station. Strong stations will produce an AVC voltage that reduces the 1DN5 gain.

Just as unusual, there is no AVC applied to the IF pentode 1U4. The control grid of this tube is fixed-biased about 1.5V below the negative end of it's filamentary cathode.

Finally, the 1R5 pentagrid converter tube get's it's RF grid bias via 3.3Meg from the AVC voltage that is developed by the detector anode inside the 1DN5. But this detector diode sits 1.5V higher than usual, because it's cathode is the second filament in the string. This added +1.5V serves as what is known as "AVC delay". This means that the 1R5 will not start having it's gain reduced until at least -1.5V of incomming carrier overcomes the +1.5V "AVC delay".

The AVC voltage that appears at the RF input grid of the 1R5 is also applied directly to the remote cutoff grid of the audio pentode in the 1DN5. Keep in mind that it's cathode is second-up in the filamentary string, so with zero input signal, the AVC voltage appears at the 1DN5 remote cutoff grid as a -1.5V bias. As signals are tuned-in that produce more than -1.5V of detected carrier, then the grid of the 1R5 pentagrid converter and the remote-cutoff grid of the 1DN5 audio pentode will go negative together to attenuate the volume.

One last peculiarity is that the 1DN5 is mounted on a Tinker-Toy module, which contains most of the resistors and capacitors in  the radio.

Summarizing, the AVC voltage is applied in the usual negative Feedback fashion to the 1R5 pentagrid converter, but is applied in Feedforward to the 1DN5 audio preamp.

Why all this strange grid bias and AVC complication? It saves the cost of a power transformer. Without a power transformer, the least inneficient way to drive the DC filaments is as a series string drawing 50mA. The series string keeps the dissipation in the 2k filament ballast resistor at only 5W. If all filaments were wired in parallel, the ballast resistor would have to supply 250mA and dissipate 20W.



The correct reference for one Motorola radio is HS-559, not HS-599.


Motorola Inc. ex: 5P32E Ch= HS-559
Fin de las contribuciones al foro de modelo