TS2 Ch= RC61
Braun; Frankfurt: TS2 Ch= RC61 [Radio] ID = 2635690 1400x933
Wählen Sie rechts durch klick. Mitglieder klicken für Download in gross.
|
|
||||
| Jahr: 1956–1958 | Kategorie: Rundfunkempfänger (Radio - oder Tuner nach WW2) | ||||
| Röhren | 7: ECC85 EF89 ECH81 EF89 EM80 EABC80 EL84 | ||||
|---|---|---|---|---|---|
| Halbleiter (Zählung nur für Transistoren) | B250C100 |
| Hauptprinzip | Superhet allgemein; ZF/IF 460/10700 kHz |
|---|---|
| Anzahl Kreise | 6 Kreis(e) AM 12 Kreis(e) FM |
| Wellenbereiche | Langwelle, Mittelwelle, Kurzwelle und UKW. |
| Spezialitäten | |
| Betriebsart / Volt | Wechselstromspeisung / 110, 125, 150, 220, 240 Volt |
| Lautsprecher | 3 Lautsprecher |
| Belastbarkeit / Leistung | 6 W (Qualität unbekannt) |
| von Radiomuseum.org | Modell: TS2 Ch= RC61 - Braun; Frankfurt |
| Material | Gerät mit Holzgehäuse |
| Form | Tischgerät, Tasten oder Druckknöpfe. |
| Abmessungen (BHT) | 545 x 395 x 280 mm / 21.5 x 15.6 x 11 inch |
| Bemerkung | drehbare Ferritantenne. |
| Nettogewicht | 11.3 kg / 24 lb 14.2 oz (24.89 lb) |
| Originalpreis | 320.00 DM |
| Datenherkunft | HdB d.Rdf-& Ferns-GrH 1956/57 / Radiokatalog Band 1, Ernst Erb |
| Literaturnachweis | HdB d.Rdf-& Ferns-GrH 1957/58 |
Alle gelisteten Radios usw. von Braun; Frankfurt
Hier finden Sie 1041 Modelle, davon 905 mit Bildern und 642 mit Schaltbildern.
Sammlung von Mitglied aus E
Sammlung von Mitglied aus D
Forumsbeiträge zum Modell
Braun; Frankfurt: TS2 Ch= RC61
Threads: 1 | Posts: 5
|
Klicks: 2285 Antworten: 4
Braun (Chassis) RC61; TS2 output transformer wiring
|
|
|
Marco Gilardetti
10.Mar.06 |
1
Gentlemen, I have an output transformer of the Braun RC61 as a spare part, and I'm planning to use it in a home made project. However, though I have the schematics, I'm having a hard time figuring out the wiring. I see three thicker cables coming out of the transformer. Plus, there are other four very thin cables of different colors, grouped in couple of two. Can some owner of the radio please check which cable goes where? I'm basically trying to use it as a simple output transformer: tube output on one side, a single 8 Ohm loudspeaker on the other. I would need four connections, but the transformer has seven. Any help would be highly appreciated. Thanks a lot. |
|
Arpad Roth † 27.3.17
10.Mar.06 |
2
E-mail adress is okay. |
|
Marco Gilardetti
10.Mar.06 |
3
Arpad, thanks a lot (I suppose your post went with my other thread, someone can move posts?). As a matter of fact, that's not the address Ake put on his website. Will sure give it a try. Cheers - M. |
|
Marco Gilardetti
23.Mar.06 |
4 Please note that the two last posts were off-topic, and the problem has not been solved yet. Will be very thankful to whoever will help! |
|
Andre Bryx
13.Apr.06 |
5
Hello Marco! I have an open Chassis here ready for shipping could took a quick look. If you have the shematics in front of you, the following is wired: Thick Black: Output for the Bass Speaker Thick Yellow: Output for the High Speakers over the 5uF capacitor Thick Brown: Output Ground Small Red: Goes to [+] of the rectifier Small Yellow: Goes to W55 / 1.5K Small Green: Goes to EL84 Anode / Pin 7 Small Black: Goes to W54 / 50K But without warranty, it depends only on my own RC61 model! Hope that helps.. Best regards, Andre |
Braun; Frankfurt: TS2 Ch= RC61
Ende Forumsbeiträge zum Modell
Ende Forumsbeiträge zum Modell
