409/3D Inland
Metz Transformatoren- und Apparatefabrik (ex TAM), Fürth
- Country
- Germany
- Manufacturer / Brand
- Metz Transformatoren- und Apparatefabrik (ex TAM), Fürth
- Year
- 1956 ?
- Category
- Broadcast Receiver - or past WW2 Tuner
- Radiomuseum.org ID
- 78258
Click on the schematic thumbnail to request the schematic as a free document.
- Number of Tubes
- 8
- Number of Transistors
- Semiconductors
- Tr.Gl.=Metal-rectif.
- Main principle
- Superheterodyne (common); ZF/IF 473/10700 kHz; 2 AF stage(s)
- Tuned circuits
- 7 AM circuit(s) 10 FM circuit(s)
- Wave bands
- Broadcast, Long Wave, Short Wave plus FM or UHF.
- Power type and voltage
- Alternating Current supply (AC) / 110; 127; 160; 220; 240 Volt
- Loudspeaker
- 4 Loudspeakers
- Material
- Wooden case
- from Radiomuseum.org
- Model: 409/3D [Inland] - Metz Transformatoren- und
- Shape
- Tablemodel with Push Buttons.
- Dimensions (WHD)
- 26 x 15.5 x 10 inch / 660 x 394 x 254 mm
- Notes
-
Metz Modell 409/3D hat 3 extra Tasten für Sprache / Jazz / Konzert.
AM-Bandbreite umschaltbar. Ferritantenne nicht drehbar.Siehe auch Exportversion 409/3D mit zwei Kurzwellen-Bereichen und UKW bis 108 MHz.
- Literature/Schematics (1)
- -- Schematic
- Author
- Model page created by Gottfried Silberhorn. See "Data change" for further contributors.
- Other Models
-
Here you find 584 models, 457 with images and 308 with schematics for wireless sets etc. In French: TSF for Télégraphie sans fil.
All listed radios etc. from Metz Transformatoren- und Apparatefabrik (ex TAM), Fürth
Forum contributions about this model: Metz Transformatoren: 409/3D
Threads: 1 | Posts: 1
Does anybody have information about this model?
After resurecting an American version of this radio, I am amazed to find that it came with a partial circuit board (just the amp section with tube sockets in it), bipolar electrolytic capactors on the speakers, use of of an EF86 in the amp section, to just name a few things.
It does lack the build quality like its competitors, SABA, Telefunken, and Grundig, but the big speaker and the push pull amp, makes this radio a "screamer"!
Since there is no schematic on RMorg. , I had to sort of figure out what's going on, by using the listed schematics for the 408/3D and 410/3D models.
The only major flaw is, that they placed the self biasing resistor directly on the circuit board(rated at 1 watt). Of coarse, the resistor was open, and needed to be replaced. When I recapped the board, I placed a 5 watt sandstone resistor seperated from the board for heat disipation.
Is there any advice someone can give regarding the tuner/clutch mechanism?
Thank you
Omer
After resurecting an American version of this radio, I am amazed to find that it came with a partial circuit board (just the amp section with tube sockets in it), bipolar electrolytic capactors on the speakers, use of of an EF86 in the amp section, to just name a few things.
It does lack the build quality like its competitors, SABA, Telefunken, and Grundig, but the big speaker and the push pull amp, makes this radio a "screamer"!
Since there is no schematic on RMorg. , I had to sort of figure out what's going on, by using the listed schematics for the 408/3D and 410/3D models.
The only major flaw is, that they placed the self biasing resistor directly on the circuit board(rated at 1 watt). Of coarse, the resistor was open, and needed to be replaced. When I recapped the board, I placed a 5 watt sandstone resistor seperated from the board for heat disipation.
Is there any advice someone can give regarding the tuner/clutch mechanism?
Thank you
Omer
Omer Suleimanagich, 28.Sep.05